Outerwear
Remember how well your outerwear worked when it was new? It kept you dry. It breathed. Now it sometimes gets soaked on the inside. What happened? The factory water repellent (DWR) has worn thin and now your sweat is condensing on the jacket’s interior. Re-treat your garment with the wrong water repellent and you’ll reduce or eliminate breathability (and have to re-treat again after a few wearings). ReviveX treatments bond solidly to both the fabric and any remaining factory DWR. As a result, ReviveX works better and lasts longer.
-
Weatherproofing
-
Repairs
How to Thread A Needle
-
-
Step 1:
Cut the end of the thread at a 45 degree angle. Stiffen the thread with saliva or bees wax. It will be easier to control through the eye than a limp thread. Hold up the needle so the eye of the needle is open toward you. If you are unable to see the eye of the needle, place a contrasting color behind the needle.
-
Step 2:
Slip the thread into the needle and pull the thread until ends are even. Knot the ends of the thread together (see Knotting The Thread). Straighten the threads and begin sewing. Pull the thread after each stitch to prevent the thread knots.
Knotting the Thread
-
-
Step 1:
After threading the needle, wrap the ends of thread around the pointer finger. Make an “X” whith the tread.
-
Step 2:
Place your thumb over the “X”. Roll the thread back and forth a couple of times between you pointer finger and thumb.
-
Step 3:
Slide the knot off your finger with your thumb, rolling the threads together towards the end of your pointer finger while pinching the thread.
-
Step 4:
I Slide the knot to the end of the thread by gently sliding the knot to the end of the thread using the end of your pointer finger and thumb.
Basic Sewing Stitches
-
-
Running Stitch
The running stitch is used to make simple seams in fabrics. It is easily completed by passing your needle in and out of the fabric at equal distances of approximately 1/4”. The stitches on the topside of your fabric should be the same length of the stitches on the underside of your fabric.
-
Backstitch
The backstitch is one of the strongest types of hand-sewn stitches. The back stitch is used for making small, tight seams that will not leak filling (sleeping bags).
-
Step 1:
Start out by sewing a couple of stitches over the same spot, and then sew a stitch with a space. Insert the needle from the underside of the fabric layers 1/8” to the left of where your stitching will begin. Pull the thread through to the knot.
-
Step 2:
Insert the needle 1/8 inch behind where the thread emerges (where your stitching will begin). Bring the needle up 1/4” beyond this insertion, and pull the thread snugly. Bring the needle up 1/4” beyond.
-
Step 3:
Viewed from the top, backstitching appears as a continuous line of even stitches; viewed underneath, the stitches are twice as long as those on top and they overlap at the ends.
Replace A Broken Zipper Slider
-
-
Step 1:
Select a slider that matches the one you are removing. The letters that are printed on the slide tell you what size you need. With a seam ripper, carefully remove stitching around lower ends of zipper tapes. Pry off metal stop at bottom of the zipper, careful not to tear the tapes at the base of the zipper teeth
-
Step 2:
Remove old zipper foot. Take new zipper slider and guide track tapes into the top grooves of the slider, pushing them through to the bottom. Use a pin if needed to work the track tapes through. Pull tapes gently to make sure slider is sitting evenly on tracks. With both tapes threaded through slider, gently pull slider up until locked track teeth appear at bottom.
-
Step 3:
Sew a new stop at bottom of the tracks with needle and thread. Sew zipper back onto garment where stitching was removed for repair.
Repair Your Outerwear
-
-
Step 1:
Make sure the inside and outside surfaces are clean. Trim loose threads. Pull the torn sections together and apply a piece of Tenacious Tape to the outside of the jacket to hold the torn sections together. The patches in the Field Repair Kit are ideal for this purpose. Check to see that you like the way the torn sections are aligned, once the adhesive sets this will be permanent. For pinholes, simply apply the Tenacious Patch to cover the hole.
-
Step 2:
Turn the garment inside out. You’ll apply Seam Grip to the inside surface for best finished aesthetics.
-
Step 3:
Inside the Jacket: Apply Seam Grip to the torn area and ¼ inch beyond onto undamaged fabric (5mm). Allow to dry level overnight. Remove the Tenacious Tape patch once the Seam Grip is dry (cured). Repair is generally permanent and will withstand washing and waterproofing treatments.
-
Speed Tip
add a few drops of Cotol 240™ to the Seam Grip before applying to the fabric. This will speed cure time to 2 hours (normally this is 4-8 hours).
Sleeve Tip
for ease of donning jackets, you can put a small piece of Tenacious Fabric Tape over the dried (cured) Seam Grip. Any color will work (as it’s inside the jacket), but fabric tape is preferred (over clear) for this application.
-
Cleaning
Maintaining Your Down Outerwear
-
-
Step 1:
Prior to washing, apply cleaner directly to heavily soiled areas. Close all zippers and Velcro® tabs.
-
Step 2:
Fill sink or tub with just enough warm water to submerge item; add ReviveX Down Cleaner. Compress item to remove air and place in water.
-
Step 3:
Rinse item repeatedly until water runs clear (at least 3 times). Gently compress or roll item (do not wring) to expel water.
-
Step 4:
Place item in washing machine for 2 spin cycles to remove excess water before drying.
-
Step 5:
Before drying, apply ReviveX Spray-On Water Repellent to the outer shell fabric. Apply liberally to shoulders, cuffs and zipper areas. Dry garment by itself in a large dryer (it needs room to tumble freely). Use heat setting recommended by garment care label (medium heat if possible).
Cleaning & Retreating Outerwear
-
-
Step 1:
Prior to washing, apply cleaner directly to heavily soiled areas. Close all zippers and Velcro® tabs.
Step 2:
Add ReviveX Synthetic Fabric Cleaner to washer. Wash garments using the delicate cycle and warm water. Whenever possible use a front loading, instead of a top loading washing machine.
-
Alternate Step 2:
If desired, hand wash garments in a sink or tub. Fill sink with just enough water to cover the garments and add cleaner. Gently knead all areas to remove dirt and stains. Rinse thoroughly until water runs clear.
-
Step 3:
Now is a good time to apply a fresh water repellent treatment. Place wet garment on a hanger. Spray ReviveX Spray-On Water Repellent or ReviveX Spray-On Water Repellent for Soft Shells on the garment exterior.
-
Step 4:
Dry using heat setting recommended by garment care label (medium heat if possible). To restore rainwear and softshells to their original water repellency, dry garments for at least 60 minutes.
-
Care
Care for Your Wool Garments
-
-
Step 1:
To maintain the itch-free softness of wool garments (such as Merino) clean with ReviveX Wool Cleaner. Wool base layers, underwear and socks should be washed after each use. Wool mid and outer layers should be cleaned when dirty and at least once per season. Most new garments are made to be machine washed. Check garment label. If hand washing is required follow these steps:
-
Step 2:
Fill sink or tub with enough water to submerge items and add ReviveX Wool Cleaner; soak for 5 minutes. Gently knead items to remove dirt and stains.
-
Step 3:
Drain sink and carefully squeeze soapy water out. Rinse until water runs clear. Place item on a clean bath towel. Roll up gently to expel water. Repeat with dry towels.
-
Step 4:
Air dry flat on a fresh towel.